APT Language

September 13, 2017 | Author: Randy Walter | Category: Computer Aided Design, Geometry, Plane (Geometry), Cartesian Coordinate System, Technology
Share Embed Donate


Short Description

Cad Cam short lecture on APT launuage,...

Description

CAD/CAM

The APT Language APT is not only the NC language; it is also the computer program that performs the calculations to generate cutter positions based on APT statements. APT is a three-dimensional system that can be used to control up to five axes. APT can be used to control a variety of different machining operations. There are over 400 words in the APT vocabulary. There are four types of statements in the APT language. 1. 2. 3. 4.

Geometry statements Motion statements Postprocessor statements Auxiliary statements

Geometry Statements: To program in APT, the workpart geometry must first be defined. The tool is subsequently directed to move to the various point locations and along surfaces of the workpart which have been defined by these geometry statements. The general form of geometry statement is this: Symbol = geometry type/descriptive data Example:

P1 = POINT/5.0, 4.0, 0.0

P1 = symbol used to identify the geometric elements (combination of six or fewer alphabetic and numeric characters Point = type of geometry element (POINT, LINE, PLANE, CIRCLE) 5.0, 4.0, 0.0 = descriptive data that defines the element precisely, completely, and uniquely

To specify a line: L3 = LINE/P3, P4 (two point line) L4 = LINE/P5, PARLEL, L3 (line L4 must pass through point P5 and be parallel to line L3 PL1 = PLANE/P1, P4, P5 (a plane defined by three points) To specify a Circle: C1 = CIRCLE/CENTER, P1, RADIUS, 5.0 (two descriptive words are used to identify the center and radius) The coordinate data must be specified in the order of x, y, z Any symbols used as descriptive data must have been previously defined. A symbol can used to define only one geometry element.

Motion Statements APT motion statements have a general format, just as the geometry statements do. The general form of a motion statement is: Motion command/descriptive data Example:

GOTO/P1

GOTO = basic motion command telling the tool what to do P1 = descriptive data telling the tool where to go At the beginning of the motion statements, the tool must be given a starting point. This point is likely to be the target point, the location where the operator has positioned the tool at the start of the job. The part programmer keys into this starting position with the following statement: FROM/TARG FROM = vocabulary word indicating that this is the initial point from which others will be referenced. TARG = symbol given to the starting point. Any other symbol can be used to define the target point

Another way to make this statement is FROM/-2.0, -2.0, 0.0 The FROM statement occurs only at the start of the motion sequence. It is convenient to distinguish between PTP movements and contouring movements when discussing the APT motion statements. Point to point motions: There are only two basic PTP motion commands: GOTO and GODLTA. GOTO = This command instructs the tool to go on a specified point. GOTO/P2 GOTO/2.0, 7.0, 0.0 GODLTA = specifies the increment move for the tool GODLTA/2.0, 7.0, 0.0 (instructs the tool to move from its present position 2 in. in the x direction and 7 in in they direction. The z-coordinate remains unchanged.

Example: Write the APT geometry and motion statements necessary to perform the drilling portion

Contouring Motions: Contouring commands are somewhat more complicated because the tool’s position must be continuously controlled throughout the move. To accomplish this control, the tool is directed along two intersecting surfaces as shown in figure. These surfaces have very specific names in APT.

Drive surface: This is the surface (pictured as a plane in figure) that guides the side of the cutter

Part surface: This is the surface (a plane) on which the bottom of the cutter rides. The reader should note that the part surface may or may not be an actual surface of the workpart. The part programmer must define this plus the drive surface for the purpose of maintaining continuous path control of the tool. Check surface: This is the surface that stops the movement of the tool in its current direction. In a sense, it checks the forward movement of the tool

The APT contour motion statement commands the cutter to move along the drive and part surfaces and the movement ends when the tool is at the check surface. There are six command words:

Example: Use of motion commands in a contouring sequence. The sequence begins with tool located at the target point P0.

Postprocessor statements To write a complete part program, statements must be written that control the operation of the spindle, the feed, and other features of the machine tool. These are called postprocessor statements. Some of the common postprocessor statements that appear in the appendix at the end of the chapter are:

Example 8.5

The MACRO statement in APT

View more...

Comments

Copyright © 2017 KUPDF Inc.
SUPPORT KUPDF